Winco HPS6000HE/E Instrucciones de operaciones descargar pdf (Pagina 15)

3180-00 60706-238

4. Spark Plug: Replace annually or every 300 hours

of operation. Always replace with the same spark

plug that came in the engine and check gap before

installing. Spark plug gap is 0.030”. Poor spark will

alsooccurifsparkplugwiredoesnottrmlyon

sparkplug.Ifthishappens,reformtheterminaltot

rmlyonsparkplugtip.

5. Carbon Canister: Designed to collect, store, and

dispose of fuel vapors created in the fuel tank / fuel

system. The canister should last the life of the unit as

long as it stays dry.

GENERATOR CARE

Proper care and maintenance of the generator is

necessary to ensure a long trouble free life.

1. Exercising The Generator - The generator

should be operated every three to four weeks. It

shouldbeoperatedforaperiodoftimesufcientto

warm the unit up and to dry out any moisture that has

accumulated in the windings. If left, this moisture can

cause corrosion in the winding. Frequent operation

of the engine generator set will also insure that the

set is operating properly should it be needed in an

emergency.

2. Generator Maintenance - Any major genera-

tor service, including the installation or replacement

ofparts,shouldbeperformedonlybyaqualied

electrical service technician. USE ONLY FACTORY

APPROVED REPAIR PARTS.

a. Bearing - The bearing used in these generators

is a heavy duty double sealed ball bearing.

They require no maintenance or lubrication.

b. Receptacles - Quality receptacles have been

utilized. If a receptacle should become cracked

or otherwise damaged, replace it. Using dam-

aged or cracked receptacles can be both dan-

gerous to the operator and destructive to the

equipment.

CLEANING

Remove dirt and debris with a cloth or brush. DO

NOT use high pressure spray to clean either the

engine or the generator. This high pressure spray

could contaminate the fuel system and the generator

components.

1. Keep the air inlet screen on both the engine and

generator free of any dirt or debris to insure proper

cooling. At least yearly, remove the blower housing

on the engine and clean the chaff and dirt out of the

enginecoolingnsandywheel.Cleanmoreoften

if necessary. Failure to keep these areas clean may

cause overheating and permanent damage to the

unit.

2. Periodicallycleanmuferareatoremoveallgrass,

dirtandcombustibledebristopreventare.

3. Onenginemufersequippedwithsparkarresters,

the spark arrester must be removed every 50 hours

for cleaning and inspection. Replace if damaged

−

ENGLISH

AIR CLEANER

Inspection

Cleaning

Dual-Filter-Element Types

Oil Change

LOWER LIMIT

GASKET

TAB

GROOVE

PRECLEANER CAP

AIR CLEANER

COVER

PAPER FILTER

ELEMENT

FOAM FILTER

ELEMENT

WING NUT

STANDARD DUAL-FILTER-

ELEMENT TYPE

WING NUT

DRAIN PLUG

UPPER LIMIT

CYCLONE DUAL-FILTER-ELEMENT TYPE

AIR CLEANER COVER

WING NUT

PAPER FILTER ELEMENT

FOAM FILTER ELEMENT

AIR GUIDE

CYCLONE HOUSING

SPECIAL PAN SCREW (3)

OIL FILLER CAP/DIPSTICK

A dirty air cleaner will restrictair flow to the carburetor, reducing

engine performance. If you operate the engine in very dusty areas,

clean the air filter more often than specified in the MAINTENANCE

SCHEDULE.

Operating the engine without an air filter, or with a damaged air

filter, will allow dirt to enter the engine, causing rapid engine wear.

This type of damage is not covered by the

Distributor’s Limited

Warranty.

Refer to pages for instructions that apply tothe air cleaner

and filter for your engine type.

Remove the wing nut from

the air cleaner cover, and

remove the cover.

Remove the wing nut from

the air filter, and remove the

filter.

Remove the foam filter from

the paper filter.

Inspect both air filter

elements, and replace them if

they are damaged. Always

replace the paper air filter

element at the scheduled

interval (see page ).

Drain the used oil while the engine is warm. Warm oil drains

quickly and completely.

Place a suitable container below the reduction case to catch the

used oil, then remove the oil filler cap/dipstick, the drain plug

and washer.

Allow the used oil to drain completely, then reinstall the drain

plug and a new washer, and tighten it securely.

Please dispose of usedmotor oil in a manner that is compatible

with the environment. We suggest you take usedoil ina sealed

container to your local recycling center or service station for

reclamation. Do not throw it in the trash or pour it on the ground

or down a drain.

Transmission oil capacity: 0.30

(0.32 US qt , 0.26 Imp qt)

Running the engine with a low transmission oil level can cause

transmission damage.

Screw in the oil filler cap/dipstick and tighten securely.

Remove the air cleaner cover and inspect the filter elements.

Clean or replace dirty filter elements. Always replace damaged

filter elements. If equipped with an oil-bath air cleaner, also check

the oil level.With the engine in a level position, fill tothe upper limit mark on

the dipstick withthe recommended oil (see page ). To check

the oil level, insert and remove the dipstick without screwing it

into the filler hole.

10 11

1 2 ... 10 11 12 13 14 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios

Winco HPS6000HE/E Instrucciones de operaciones Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Generadores De Poder Winco HPS6000HE/E