Winco HPS6000HE/E Instrucciones de operaciones Pagina 9
- Pagina / 20
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9
3180-00 60706-238
WARNING: PERSONAL INJURY
Lead acid batteries produce explosive hydrogen
gas when charging. Keep sparks, ames, and
burning cigarettes away from the battery. Ventilate
the area when charging or using the battery in an
enclosed space. Lead acid batteries contain sulfuric
acid, which causes severe burns. If acid contacts
eyes, skin or clothing, ush well with water. For con-
tact with eyes, get immediate medical attention.
BATTERY CHARGING
Unitsequippedwithelectricstarthaveasmally-
wheelchargerbuiltintotheengineywheelassem-
blyforrechargingthestartingbattery.Thisywheel
charger generates a small AC current that passes
through a diode assembly to produce a DC charg-
ing current of about 1 to 3 AMPS. This circuit is not
designed to be used as a battery charging circuit to
recharge dead batteries.
OPTIONAL DOLLY KIT
An optional dolly kit is available for this generator.
The dolly kit comes with instructions and parts list.
Afterinstallingthedollykit,letheinstructionsand
parts list in the back of this manual for future refer-
ence.
OIL ALERT SYSTEM
This WINCO generator is equipped with a low oil
shutdownsystem.Thisengineusesanoatswitch
mounted inside the engine. If the oil level drops
below a certain point the low oil module on the
engine will shut it down. This low oil warning system
will automatically stop the engine before the oil level
reaches a critical danger point. This feature is de-
signed to prevent costly repairs and downtime.
CAUTION: EQUIPMENT DAMAGE
Allowing the engine to shutdown repeatedly on
low oil level may cause excessive wear which can
be cumulative.
INITIAL START UP
The throttle control on these generators is preset and
locked to operate at 3600 RPM (nominal) with no load
speed set at 3690 RPM. Only a trained service tech-
nician should be allowed to adjust this speed setting.
NOTICE: ENGINE START LOCKOUT
This unit will not start if it is low on oil. The lu-
bricating oil level must be at the full mark before the
engine will start and run.
BASIC OPERATION
MANUAL STARTING (Gasoline Only)
Refer to the engine manual for additional starting,
operating, and stopping instructions.
1. Checkoillevel.Rellasneeded.
2. Turn on the fuel supply by moving the fuel lever
to the “ON” position.
NOTE - There is a second fuel valve under the fuel
tank that is used when removing the tank. This valve
is normally left on.
3. Move the choke lever to the “CLOSED” position.
To restart a warm engine, leave the choke lever in
the “OPEN” position
OPERATION
SAFE OPERATING PRECAUTIONS
STARTING THE ENGINE
ELECTRIC STARTER TYPESEXCEPT ELECTRIC
STARTER TYPES
ENGLISH
OFF
OONN
MMAAXX..
1/3
POSITION
THROTTLE LEVER
ENGINE SWITCH
ON
MMIINN..
OOPPEENN
CLOSE
D
CLOSED
OOPPEENN
E
NGINE SWITCH
ENGINE SWITCH
FUEL VALVE LEVER
OONN
CCLLOOSSEEDD
C
HOKE LEVER
ON
ON
ON
ON
ON
MMIINN..
CH
OKE ROD (applicable types)
4
Before operating the engine for the first time, please review the
SAFETY INFORMATION
section on page and the
BEFORE
OPERATION CHECKS
on page .
Review the instructions provided with the equipment powered by
this engine for any safety precautions that should be observed
with engine startup, shutdown or operation.
Carbon monoxide gas is toxic. Breathing itcan cause
unconsciousness and even kill you.
Avoid any areas or actions thatexpose you to carbon
monoxide.
Move the fuel valve lever to the ON position.
To start a cold engine, move the choke lever or choke rod
(applicable types)to the CLOSED position.
Move the throttle lever away from the MIN. position, about 1/3
of the way toward the MAX. position.
Some engine applications use a remote-mounted choke control
rather than the engine-mounted choke lever shown here. Refer
to the instructions provided by the equipmentmanufacturer.
To restart a warm engine, leave the choke lever or choke rod in
the OPEN position.
Some engine applications use a remote-mounted throttle control
rather than the engine-mounted throttle lever shown here. Refer to
the instructions provided by the equipmentmanufacturer.
Turn the engine switch to the ON position.
3.
4.
1.
2.
2
3
OPERATION
SAFE OPERATING PRECAUTIONS
STARTING THE ENGINE
ELECTRIC STARTER TYPESEXCEPT ELECTRIC
STARTER TYPES
ENGLISH
OFF
OONN
MMAAXX..
1/3
POSITION
THROTTLE LEVER
ENGINE SWITCH
ON
MMIINN..
OOPPEENN
CLOSE
D
CLOSED
OOPPEENN
ENGINE SWITCH
ENGINE SWITCH
FUEL VALVE LEVER
OONN
CCLLOOSSEEDD
C
HOKE LEVER
ON
ON
ON
ON
ON
MMIINN..
CH
OKE ROD (applicable types)
4
Before operating the engine for the first time, please review the
SAFETY INFORMATION
section on page and the
BEFORE
OPERATION CHECKS
on page .
Review the instructions provided with the equipment powered by
this engine for any safety precautions that should be observed
with engine startup, shutdown or operation.
Carbon monoxide gas is toxic. Breathing itcan cause
unconsciousness and even kill you.
Avoid any areas or actions thatexpose you to carbon
monoxide.
Move the fuel valve lever to the ON position.
To start a cold engine, move the choke lever or choke rod
(applicable types)to the CLOSED position.
Move the throttle lever away from the MIN. position, about 1/3
of the way toward the MAX. position.
Some engine applications use a remote-mounted choke control
rather than the engine-mounted choke lever shown here. Refer
to the instructions provided by the equipmentmanufacturer.
To restart a warm engine, leave the choke lever or choke rod in
the OPEN position.
Some engine applications use a remote-mounted throttle control
rather than the engine-mounted throttle lever shown here. Refer to
the instructions provided by the equipmentmanufacturer.
Turn the engine switch to the ON position.
3.
4.
1.
2.
2
3
- HPS6000HE/I 1
- SAVE THESE INSTRUCTIONS 2
- USING THE MANUAL 2
- SAFETY INFORMATION 3
- TESTING POLICY 4
- INTENDED USES 4
- RESTRICTED USES 4
- UNIT CAPABILITIES 4
- PREPARING THE UNIT 5
- GASOLINE 6
- NG FUEL INSTALLATION 6
- Gasoline 1.67 Gal/HR 7
- Fuel Pressure Table 7
- FROM GASOLINE TO NG 8
- FROM NG TO GASOLINE 8
- OPERATION 10
- CONNECTING THE LOADS 12
- GROUNDING 13
- ENGINE CARE 14
- GENERATOR CARE 15
- CLEANING 15
- TROUBLESHOOTING 16
- WIRING DIAGRAM 17
- 24 MONTH LIMITED WARRANTY 18
- WARRANTY STATEMENT 19
- 60706-238 20
Relacionado con productos y manuales para Generadores De Poder Winco HPS6000HE/E
(16 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales